Search Results

An experimental study is performed to investigate the effects of charge motion control on in-cylinder fuel-air mixture preparation and combustion inside a direct-injection spark-ignition engine with optical access to the cylinder. High-pressure production injector is used with fuel pressures of 5 and 10 MPa. Three different geometries of charge motion control (CMC) device are considered; two are expected to enhance the swirl motion inside the engine cylinder whereas the third one is expected to enhance the tumble motion. Experiments are performed at 1500 rpm engine speed with the variation in fuel injection timing, fuel pressure and the number of injections. It is found that swirl-type CMC devices significantly enhance the fuel-air mixing inside the engine cylinder with slower spray tip penetration than that of the baseline case without CMC device. Combustion images show that the flame growth is faster with CMC device compared to the similar case without CMC device.

A separator is a membrane that prevents the physical contact between the positive and negative electrodes while enabling ionic transport. The integrity of the separator is vital to the performance and reliability of a battery. This paper presents finite element stress analysis for the separator in a lithium-ion battery using a macro-scale battery cell model. In this model, the porous electrodes were treated as homogenized media and represented with the effective properties estimated using the rule of mixtures. To compute the deformation due to lithium (Li) intercalation & deintercalation and temperature variation, the Li concentration distribution and temperature change due to electrochemical reactions must be known. These parameters were computed using a multi-physics model in COMSOL and mapped to the macro-scale model in ANSYS. Numerical simulations were conducted to identify the locations and magnitudes of the maximum strain and stress of the separator in the pouch cell.

This paper discusses simplified lumped parameter thermal modeling of power train components. In particular, it discusses the tradeoff between model complexity and the ability to correlate the predicted temperatures and flow rates with measured data. The benefits and problems associated with using a three lumped mass model are explained and the value of this simpler model is promoted. The process for correlation and optimization using modern software tools is explained. Examples of models for engines and transmissions are illustrated along with their predictive abilities over typical driving cycles.

For designing new products or developing new specifications, the reliability performance of systems and components experienced by the customer provides invaluable information for the engineer. This information, not only provides for the visibility of reliability requirements, but also an awareness of potential degradation of the systems and components during its life cycle. In this paper, a method is presented for predicting vehicle system and component reliability from vehicle fleet repair data. This method combines sampling stratification, computer data analysis and statistical modeling techniques into a reliability analysis procedure to provide reliability prediction. Specifically, published vehicle fleet data was used to provide the basis for predicting the vehicle system and component reliability at any mileage level.

In the design of small off-highway and utility engines for compliance with increasingly stringent emissions standards, one component which can potentially reduce engine exhaust-gas emissions without necessitating changes in other, more costly parts is the spark plug. From studies carried out in automobile engines, benefits have been reported when using different spark-plug electrode shapes or when aligning the plugs in the cylinder head in preferred directions. However, these benefits, observed in automotive overhead valve engines with well-mixed charges, have generally been modest? and spark plugs of conventional shape remain the most widely used today. In the case of off-highway and utility engines, which operate at substantially higher air-fuel ratios, often with poorly-mixed charges, the potential for improving performance by changing spark-plug shape has not been explored.

This paper discusses the feasibility and issues associated with integrating a consumer off-the shelf product into a vehicle. For this evaluation, we selected a handheld personal computer (HPC), cellular telephone and modem to integrate with the vehicle audio, climate and system controls. Connectivity between the HPC and the vehicle is established by the use of the standard infrared serial data link that comes with the HPC. Connectivity outside the vehicle uses a cellular telephone for voice and a cellular digital packet data (CDPD) modem for data. This system is built into the Dodge ESX-2 hybrid powered concept vehicle for demonstration.

The rapid growth of information technology has the potential to affect many of the reasons why people drive. The Internet is arguably the most significant recent milestone in the growth of information technology. This paper examines the ways Internet communication might affect the travel experience by a) eliminating traditional reasons for personal travel, b) providing new reasons, c) changing the balance between personal and freight travel, and d) changing trip length distribution. Changes of the types listed could affect the product demand "mix" for electric, hybrid-electric and fuel cell vehicles being developed.

This paper reports on the experimental study of carbide and polycrystalline diamond (PCD) drills used for drilling composite/titanium stacks. Materials systems used in this study were multi-directional carbon fiber in an epoxy matrix and titanium 6Al-4V. The drill materials included tungsten carbide (WC; 9%Co ultra fine grain) and polycrystalline diamond (PCD; bimodal grade). Torque and thrust force were measured during the drilling experiments. Tool wear of both drills was periodically examined during the drilling tests using various microscopic techniques such as optical and Scanning Electron Microscope (SEM). Effect of tool materials and process condition on hole quality parameters such as hole diameter, surface roughness, and titanium burrs, were examined. Dissimilar mechanical and thermal properties of the stacks affected the tool life and resulted in the decreased hole quality for both cutting tool materials, although to a differing degree.

A device has been designed and built to allow one to systematically investigate the dynamical behavior of a wide variety of torsional vibration absorbers (TVAs). These are devices that can passively absorb the torsional vibration of a wide range of rotating systems. The testing device allows different operating conditions to be studied and similarities and discrepancies between theoretical predictions and experimental results can be made. The manuscript emphasizes the design and capabilities of the device and discusses the instrumentation of the system. It also presents a limited number of experimental results along with the associated theoretical predictions.

Many engineering systems create unwanted noise that can be reduced by the careful application of engineering noise controls. When this noise travels down tubes and pipes, a tuned resonator can be used to muffle noise escaping from the tube. The classical examples are automobile exhaust and ventilation system noise. In these cases where a narrow frequency band of noise exists, a traditional engineering control consists of adding a tuned Helmholtz resonator to reduce unwanted tonal noise by reflecting it back to the source (Temkin, 1981). As long as the frequency of the unwanted noise falls within the tuned resonator frequency range, the device is effective. However, if the frequency of the unwanted sound changes to a frequency that does not match the tuned resonator frequency, the device is no longer effective. Conventional resonators have fixed tuning and cannot effectively muffle tonal noise with time-varying frequency.

The reliability of an electronic sensor in the automotive applications is assessed using data from Fleet Test and proving ground Vehicle Endurance test. These nonfailure data are multiply censored at different mileage. Reliability analysis of data with no failure is rarely discussed in most reliability literature. This paper applies the Weibull maximum likelihood analysis based on known values of the Weibull shape parameter to extract useful reliability information. The well-known Weibayes and Weibest methods are subsets of the discussed approach. The sensitivity of the change of reliability levels over a range of Weibull shape parameter values is also examined in our case. The Huang-Porter (1991) approach of obtaining a reliability lower bound regardless of the Weibull shape parameter values is also applied and its potential of practical application is discussed. Practical limitations of all methods are discussed.

Higher horsepower per liter engines have put more demand on the crankshaft, often requiring the use of forged steel. This paper examines cost reduction opportunities to offset the penalties associated with forged steel, with raw material and machinability being the primary factors evaluated. A cost model for crankshaft processing is utilized in this paper as a design tool to select the lowest cost material grade. This model is supported by fatigue and machinability data for various steel grades. Materials considered are medium carbon, low alloy, and microalloy steels; the effects of sulfur as a machining enhancer is also studied.

A computer-controlled body panel testing machine has been used to quantify stiffness and dent resistance of body panels at Chrysler. The influence of yield strength and local reinforcement on the mechanical behavior of automotive door panels has been investigated. Medium strength steels in the range of 210 -240 MPa yield strength have produced significant improvements in dent resistance over a 160 MPa yield strength steel. Considerable improvements in dent resistance can also be attributed to the use of local, adhesively attached, glass fiber reinforcement patches. The effects of boundary conditions and panel shape on stiffness and dent resistance are illustrated in this application.

The purpose of this work was to develop a fiber optic imaging system for use in flow visualization studies at the Michigan State University Engine Research Laboratory. A flexible fiber optic image carrier was coupled with a high speed rotating prism camera to create a unique imaging system which can easily reach remote location test sites. The flow visualization study was conducted on a motored 3.5 L four-valve engine test rig. A 40 watt pulsed copper vapor laser was synchronized with the camera to produce motion picture film at 5000 frames per second (fps). The image carrier which is attached to the camera contained an 80 degree field of view (FOV) tip adapter for viewing the entire cross-sectional area of the cylinder. The area imaged was a radial plane located 3 cm from the intake valves. The engine rig was motored at 850 rpm with a flow rate of 18 kg/hr. Entrained microballoon seeding particles were filmed as they traveled through the cylinder.

The mechanical behavior of a commercially available single layer polypropylene (PP) separator was investigated using a dynamic mechanical analyzer (DMA). Samples were tested along the machine direction (MD) and transverse direction (TD). The tensile stress-strain, tensile creep and viscoelastic behaviors were studied. Experiments were performed in two conditions: (1) dry and (2) wet, i.e., samples submersed in dimethyl carbonate (DMC). The experimental results revealed that the mechanical properties of the separator were much lower while being submersed in DMC. This finding suggests that the mechanical properties measured at a dry condition may not be sufficient to represent the in-situ material behavior. Therefore, it is important to conduct material characterization in an environment close to the service condition.

This work presents a method for simultaneously capturing visible and infrared images along with pressure data in an optical Diesel engine based on the International 4.5L VT275 engine. This paper seeks to illustrate the merits of each imaging technique for visualizing both in-cylinder fuel spray and combustion. The engine was operated under a part load, high simulated exhaust gas recirculation operating condition. Experiments examining fuel spray were conducted in nitrogen. Overlays of simultaneously acquired infrared and visible images are presented to illustrate the differences in imaging between the two techniques. It is seen that the infrared images spatially describe the fuel spray, especially fuel vapors, and the fuel mixing process better than the high-speed visible images.

In this paper results are presented from a study that investigates the use of centrifugally driven pendulum vibration absorbers for the attenuation of engine torsional vibrations. Such absorbers consist essentially of movable counterweights whose center of mass is restricted to move along a specified path relative to the rotational frame of reference. These devices are commonly used in light aircraft engines and helicopter rotors. The most common designs use a circular path for the absorber, tuned to a particular order of rotor disturbance, although more recent developments offer a wider variety of paths. Our goal here is to evaluate the system performance for a range of path types with different types of tuning. This analytical study is carried out for a simple mechanical model that includes a rotor and an absorber riding along a quite general path. Approximate solutions are obtained using a perturbation scheme and compared with detailed computational results.

This study analyzes the vibration characteristics of the valve train of a 2.0L SOHC Chrysler Corp. Neon engine over a range of operating speeds to investigate and demonstrate the advantages and limitations of various dynamic measurements such as displacement, velocity, and acceleration in this application. The valve train was tested in a motoring fixture at speeds of 500 to 3500 camshaft rpm. The advantages of analyzing both time and frequency domain measurements are described. Both frequency and order analysis were done on the data. The theoretical order spectra of cam displacement and acceleration were computed and compared to the experimental data. Deconvolution was used to uncover characteristic frequencies of vibration in the system. The theoretical cam acceleration spectrum was deconvolved from measured acceleration spectra to reveal the frequency response function of the follower system.

A Methanol Concentration Smart Sensor has been developed to support the demand for alternately fueled vehicles operating on blends of methanol and gasoline in any mixture up to 85% methanol. The sensor measures concentration by exploiting the difference in dielectric properties between methanol and gasoline. The measurement is made based on the distributed capacitance of a coil of wire, contained in a reservoir through which the fuel passes. This signal, along with temperature compensation inputs, is then fed to an integral microprocessor, which provides a voltage output proportional to the methanol concentration of the fuel. The Powertrain Controller uses this information to modify injector pulse width and provide proper spark advance. This paper will explain the sensor's development methodology and function.

Typical sand-casting techniques have been shown to be inappropriate in pouring particulate reinforced aluminum metal matrix composite (Al-MMC) castings. New gating/risering configurations were necessary to produce castings of acceptable soundness. Several automotive components, including brake rotors, cylinder liners and camshaft thrust plates, were prepared using special techniques. Initial durability test results of several Al-MMC prototype components are presented.